Wednesday, January 9, 2013

The Votum Nauta

Heretofore, this Blog has been a little heavy on the science and a little light on the shenanigans.  Well, grab your grog and accordion, because a blog post to which there has been much allusion is finally here: it is time for the best (and only) tale from my sea-faring days.

You didn't think this hat was for show, did you?

Fans, it is no secret that I love adventure.  Sometimes adventure finds me.  Often enough, though, one is required to build adventure from the ground up.  In the summer of my twentieth year (being nineteen years of age, young, and crazy) my schemes skewed to sailing.  Being an engineer, my schemes revolved around making my own vessel.

Of course, this would not be a good post without tales of my hilarious near-failure subsequent catastrophe.  It turns out that building a ship is hard.  Really hard.  Below is a rough sketch of my design.


For some reason I deemed it necessary to make the sides of the ship three feet high.  To handle the pitching and rolling of the open sea, perhaps?  That's about as good an explanation as any.  Whatever the reason, the result was a ship with an impractically high center of gravity.  Its first time in the water, the ship nearly capsized.

In retrospect, this experience should have been a pretty clear omen.

A few days, much pacing, and one relatively simple integral later (thank you, Professor Callender) I had a solution.  By weighing down the boat with a sizable chunk of ballast, I could get its center of gravity to be below the waterline, thereby (hopefully) stabilizing this conglomeration of plywood enough to work on other issues like the sails, mast, and multiple hull leakages.  My calculations called for nearly four hundred pounds of ballast.

This one math problem was the only scientific part of the process.  The hull was shaped by doodling on a piece of paper, saying to myself "hey, that looks cool!," and drawing it up in the Solidworks software program.  The mast was a hapless alder tree I had hewn (with an axe, because sometimes the old ways are best) and trimmed (with a chainsaw, because I didn't have all day).  The hull was sealed with liberal applications of deck caulking, a substance known in the State of California to cause birth defects and known in the State of Oregon to fail horrendously at providing a waterproof seal on things that should definitely have a waterproof seal.  The sails were constructed in the same manner as the hull (which I will hereby patent as the "Hey, That Looks Cool!" method).

So perhaps building a ship isn't hard as long as you take time to do things right - which I clearly did not.

One spectator described it (and fittingly so) as a "wooden bathtub."  When empty and dry I could barely lift the thing; when seated I couldn't reach the sails; when standing I ran the serious risk of capsizing.  THIS PLYWOOD BEAST took on water constantly, could barely catch wind, and was awkward and unbecoming to manage.  I loved her dearly.

After one trial run on a placid day at a charitable lake, I deemed her seaworthy. Or, as close to the sea I was willing to get.  In this instance, "sea" was the Siuslaw River, a few miles from the open ocean.  I found a spot (at high tide on the mud flats) to weigh anchor.  The water at this point was still and came close to the highway.  Even at high tide, though, the keel scraped bottom.  It was several yards of ungainly paddling until I reached passable water.

At this point, though, I encountered another difficulty: the sails had been shaped and rigged by a lunatic.  They were designed to look like sails, not to be sails.  With the right wind I probably could have found some means of propulsion, but there was none.  Only the river's current (gentle as it was) supplied any force.  The issue here is that steering with a rudder assumes the boat is somehow propelled.  Bobbing up and down with the waves, a rudder does little good to actually change the direction of the boat.  So for about two miles I drifted, hauling as best I could with my tiny makeshift paddle, until at last I saw the waterfront of my beloved Florence passing me on the right.
Here I faced the most serious problem: the current swept me to the south bank, but town (and my egress) were on the north.  With about a quarter mile of passable river to go (and the ocean to greet me should I overshoot), my paddling began to increase in speed and intensity.

Florence, Oregon is known for its iconic bridge.  What is not seen from shore, however, is that the bridge funnels the river into a surprisingly choppy and unrelenting force of water.  On some level it was a dear wish of mine to sail gloriously under this bridge and laugh like the mad captain I fancied myself.  When I fantasized the moment in my head I imagined many things, chief among them the soundtrack from Pirates of the Caribbean.  I did not imagine the water pooling above the already-soaked sandbags in the bottom of my ship, nor being hamstrung by the lack of wind.  The funneling effect caught me quite unaware, as did being tossed helplessly beneath the bridge.  Backward.


The conclusion of this tale is rather uninspiring.  I pulled ashore, wet, sandy, and proud.  My mother met me there, trying to maintain her usual calm demeanor over obvious distress.  Somehow I got the thing back into the truck bed from whence it came, and in time it returned to the backyard from where it was built.  Its hull now rotted in that backyard until last week, when I found myself splitting the familiar hull back into its constituent boards.

"But Blair," exclaims the reader, "how can you so brashly cast aside this symbol of your youth and brevity?  How can you allow her to rot and burn?  Is there so little respect for your boat?  Was this only another project?"
First of all, hypothetical reader, you are entirely too dramatic.  Yes, it was hard to tear her apart, but the time had come.  More importantly, it is the hull that is being burned.  The ship lives on my wall in the nameplate.

If you are a reader of titles (specifically the title of this post) you already know her name: The Votum Nauta.  I always thought the use of Latin in everyday life rang of a pretentious nature, but somehow I couldn't resist it here (thank you, Google translate).  Yes, it seems incongruous to use so noble a name for such a leaky plywood tub, but I feel it made sense.  "Votum Nauta" translates roughly to "Hope Sailor," as in "One who Sails on Hope" or "This Boat is held together with hope and prayers."

Though I jest, there is something very important in this.  The Votum Nauta was a flawed project, yes, but it was a project directed by my will.  Its design was mine, the sweat and challenges in its creation were mine, its fruition and fateful (though happily uneventful) journey were mine, and its heart - the heart that says we can by the strength of our hands and the courage of our hearts build something and bear it against nature - that will always be mine, even if the hull burns and the nameplate fades.
Because our adventure, dear readers, is exactly what we make it to be.


Happy sailing.







Credit where it's due:

Pictures taken by Rachel Pearson

1 comment:

  1. Nice post Blair! A toast to the best plywood and tarp boat, to the adventures that went with it and to the story you will have on hand for future generations. Happy Birthday, Blairp, and happy sailing this year!

    ReplyDelete